Zoom GFX-5 Spécifications télécharger pdf (Page 4)

ZOOM GFX-5

Getting Ready to Play

Inserting the batteries

To use the GFX-5 on battery power, insert batteries

as shown below.

Turn the unit over and open the battery

compartment cover. (Push the tab to

unlock and then raise the cover.)

Insert the batteries with correct (+) (-)

polarity into the battery compartment.

Close the battery compartment cover.

(Make sure that the tab is properly

engaged.)

OTE

• When not using the unit for an extended

period, remove the batteries to prevent the

possibility of damage by leaking battery ﬂuid.

• When the indication “BATT” appears on the

display, the batteries are almost exhausted.

Replace the batteries as soon as possible

with fresh ones.

Getting connected

Make sure that the ampliﬁer and the

GFX-5 are switched off.

Turn the volume at the ampliﬁer to minimum.

To power the unit from the AC adapter,

insert the small plug of the adapter cable

into the [DC IN] jack on the GFX-5. Then

plug the adapter into an AC outlet.

Connect the guitar to the [INPUT] jack of

the GFX-5, using a mono cable.

Connect the [OUTPUT] jack of the GFX-5

to the guitar amp, using a mono cable.

To monitor the sound with headphones,

plug the phones into the [PHONES] jack.

Turn power on in the following order:

GFX-5

→

ampliﬁer.

OPEN

Battery compartment cover

GFX-5 bottom

Tab

Four IEC R6 (size AA)

batteries

Battery

compartment

cover

Battery polarity

alternates

for each slot.

BATT

Getting Ready to Play

ZOOM GFX-5

OTE

If you turn the GFX-5 on while the ampliﬁer is

already powered up, damage to the speaker may

result. Always turn power to the ampliﬁer on last.

When turning off the system, proceed in the

opposite order.

Raise the volume setting of the

instrument and ampliﬁer, and adjust the

[LEVEL] knob on the rear panel of the

GFX-5.

While playing your instrument, turn the

[ENERGIZER] knob until the sound quality

is as desired.

The [ENERGIZE] knob serves to match the unit to

the playback environment. As you turn the knob,

the display changes as follows.

Turning the knob clockwise emphasizes the low

range, and turning it counterclockwise emphasizes

the high range. The “oF” setting means that the

Energize function is turned off.

INT

The Energize setting applies to the output sound

of all signals except those from the [AUX IN] jack.

To turn the system off, proceed in the

opposite order than when turning it on.

Energize setting

(oF, 1 - 30)

ENERGY

Guitar

Guitar amps

Headphones

CD player or other source

AC adapter

Connect the guitar output

jack to the [INPUT] jack

on the GFX-5.

To sample a signal from a CD or MD

player or similar, connect the player

output to the [AUX IN] jack.

Loop the cable of the AC adapter

around the hook before connecting it

to the [DC IN] jack. This will prevent

the plug from being disconnected if the

cable is accidentally pulled.

Connect the separately available AC

adapter (ZOOM AD-0006) here.

When using only one guitar amp, connect it to the

[OUTPUT L/MONO] jack. By connecting another guitar

amp to the [OUTPUT R] jack, you can achieve reverb

and chorus sound with a wide stereo spread.

1 2 3 4 5 6 7 8 9 ... 18 19

Commentaires sur ces manuels

Pas de commentaire

Zoom GFX-5 Spécifications Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Pédale de musique Zoom GFX-5