Zoom MRS-4 Spécifications télécharger pdf (Page 188)

ZOOM MRS-1608

188

Troubleshooting

If there are problems during operation of the MRS-1608, check the following points ﬁrst.

◆

No sound, or sound is very weak

• Check the connections to your monitor system, and the

volume setting of the system.

• Make sure that the status keys in the mixer section are

lit in green and that the faders are raised. If a key is out,

press it to make it light up in green.

• Make sure that the master fader is raised.

• If a scene with the volume lowered has been assigned

to a mark, the volume will automatically be lowered

when that mark is reached. Delete the scene that is

assigned to the mark (

→

p. 85).

• The recorder will not operate when the [RECORDER]

key is out. Press the [RECORDER] key so that the key

is lit.

◆

Operating the fader does not affect the

volume

On channels for which stereo link is turned on, the fader

of the even-numbered channel will have no effect. Either

turn stereo link off (

→

p. 82), or operate the fader of the

odd-numbered channel.

◆

The display indicates “Don’t Play” and

playback is not possible

The recorder will not operate in the current screen. Press

the [EXIT] key several times to switch to the main screen.

◆

No sound from input signal, or sound is very

weak

• Make sure that the respective [ON/OFF] key of the

input is lit.

• Make sure that the respective [INPUT] control or the

[GUITAR/BASS INPUT] control is raised.

• Make sure that the [REC LEVEL] control is raised. If

it is raised, temporarily turn it down and then up again.

◆

The indication “Stop Recorder” is shown on

the display, and operation is not possible.

The current operation is not possible while the recorder is

operating. Press the STOP [

] key to stop the recorder.

◆

Cannot record on a track

• Make sure that you have selected a recording track.

• Check whether you have run out of free space on the

hard disk (

→

p. 167).

• Recording is not possible if the project is write-

protected. Either turn protect off (

→

p. 169), or use a

different project.

•

While the 8-track recording function (

→

p. 45) is active,

recording on tracks 9/10 – 15/16 and the master track is

not possible. To record on these tracks, turn off 8-track

recording.

◆

The signal from an instrument or mic

connected to an INPUT jack is not available

When instruments/mics are connected to jacks with the

same number on both the front panel and rear panel

(INPUT 1 and GUITAR/BASS INPUT 1, or INPUT 2

and GUITAR/BASS INPUT 2), the front panel jack has

priority.

◆

The recorded sound is distorted

• Check whether the input sensitivity setting ([INPUT]

and [GUITAR/BASS INPUT] controls) and recording

level setting ([REC LEVEL] control) are appropriate.

•Lower the fader so that the 0 (dB) dot of the level meter

does not light.

• If the EQ gain of the track mixer is set extremely high,

the sound may be audibly distorted even if the fader is

lowered. Set the EQ to an appropriate value.

• When the insert effect is applied to the input, check

whether the effect output level (patch level) setting is

appropriate.

Problems during playback

Problems during recording

1608E.book 188 ページ２００４年４月１９日　月曜日　午前１０時４４分

1 2 ... 183 184 185 186 187 188 189 190 191 192 193 ... 223 224

Zoom MRS-4 Spécifications Page 188

Commentaires sur ces manuels

Zoom MRS-4 Spécifications Page 188

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel d'enregistrement Zoom MRS-4