Zoom ADSL X6v Guide de l'utilisateur

X6v VoIP Features TECHNICAL REFERENCE

Note: You must change the VoIP Subsystem IP/DNS configuration settings first to the new subnet if you change the LAN subnet of your X6v. HTTP / Teln

Parameter Description Default Configuration Update Periodic Delay(s) Periodic delay between configuration update checks (in seconds - limit 4,294,9

Parameter Description Default Debug Level SIP Session Initiation Protocol debug 0 Debug Level Net Network debug 0 Debug Level PMP Port Mapping Pro

4 VoIP Accounts You can use the VoIP > Advanced VoIP Setup > VoIP Accounts menu to configure user accounts for up to four providers. The menu it

The VoIP Express Setup page is affected by settings on the My VoIP Account page. Six parameters on this page are drawn from the My VoIP Account page,

Parameter Description Default Auth Domain Specifies the authentication domain name corresponding to the Authentication User Name. This field must m

Parameter Description Default Dial Prefix Contains the dial string pattern matching used to distinguish and route calls to a VoIP service provider

Parameter Description Default My Caller ID When I Call Someone Holds the number that can be displayed at the receiving party’s phone when the user

Parameter Description Default ReReg Interval (s) Sets the default registration update period in seconds. Once the period has expired, the VoIP Su

5 VoIP Parameters You can use the VoIP > Advanced VoIP Setup > VoIP Parameters menu to configure various common aspects of the VoIP Subsystem de

RTP Protocol Parameters Parameter Description Default Base RTP port (1024-65535) The minimum IP port number for RTP traffic. Can be used in conjunc

6 SIP Parameters You can use the VoIP > Advanced VoIP Setup > SIP Parameters menu to configure particular aspects of the Session Initiation Prot

Parameter Description Default NAT Keep Alive Enable Send periodic SIP messages to keep port mapping active Enabled NAT Keep Alive Interval (s) Per

SIP Protocol Timers Parameter Description Default SIP Timer INVITE Expires (s) The time (in seconds) after which an INVITE request expires. 180 SIP

7 Regionalization You can use the VoIP > Advanced VoIP Setup > Regionalization menu to configure the VoIP Subsystem for local operating convent

A negative dBm level can be offset by ipbx_tone_gain. Allowed values for freq are from 0 to 3000Hz. Allowed values for db levels are from –1 to –40 dB

Parameter Description Default (North America) Station Call Waiting Tone Default Call waiting pattern for station to station calls. Applies to mul

Standard Ringing Patterns Ring patterns are specified by a list of values indicating the frequency, number of on/off transitions, and Ring On/Ring Off

Distinctive Ringing Patterns Parameters Parameter Description Default (All Regions) Distinctive Ring 1 Specifies the pattern for Ring 1 20 2 0 200

Voice and Tone Parameters The parameters in the following sections control the connection to the local phone (FXS) port on the VoIP Subsystem. This i

Contents 1 INTRODUCTION ...

SLAC Configuration Parameters Parameter Description Default Port Impedance (See the Values for Port Impedance table.) Synthetic impedance matching

Index Default Country 4 270 + 750 || 150 nF Sweden/CTR21 5 220 + 820 || 120 nF Germany/Austria/Australia/New Zealand #1 6 220 + 820 || 115 nF Bul

Parameter Description Default Caller ID Type 1 Mode Caller ID type 1 (on-hook) mode (None, Belcore MDMF, Belcore SDMF, ETSI WINK, ETSI RING, DTMF)

CODEC Command Strings The CODEC initialization commands provide a method to set up the device for unusual conditions. Do not change the default value

8 Subscription Services You can use the VoIP > Advanced VoIP Setup > Subscription Services menu to configure the VoIP Subsystem for the specifi

Parameter Description Default Distinctive Ring Enables customer use of distinctive ring service Enabled Disturb Accept Enables customer use of do

Dialing Parameters Parameter Description Default Mode Mode allows selection of treatment of * and # as the leading digit of a dial string. These ch

Parameter Description Default Configure PSTN Dial Pattern (See VoIP and PSTN Dial Patterns, below.) Used to configure how the VoIP Subsystem handle

You can use the dial patterns to change which calls are sent via VoIP, and which are sent to the PSTN. For example, you might want to send all local

Parameter Description t Set digit timeout to default for current pattern. - (dash) Human-readable spacing which is ignored. (space) Human-readable

CODEC CONFIGURATION...

#[1-9]e#r5xp3r*x is a string that is identical to the previous two, except for the first digit. This string supports cases where service providers us

. 976 numbers in the US are premium-rate local numbers that may incur high per-minute charges. 1800r7x Recognize a 1800XXXXXXX number This tells the s

Bridging from PSTN to VoIP Parameter Description Default Bridge From PSTN to VoIP Enable or disable the bridge Disabled Auto Answer PSTN (FXO) Cal

Emergency Services and eServices Events The emergency services numbers follow the same rules as those defined for the pattern matching strings in Dial

9 User Configuration You can use the VoIP > Advanced VoIP Settings > User Configuration menu to configure the VoIP Subsystem's user-specif

Parameter Description Default Call Forward Priority Enables or disables priority call forward Disabled Call Forward Always Number Specifies the

Parameter Description Default Block Listed Outgoing Calls Enables or disables the blocking of outgoing calls from specific numbers in the Blocked

Parameter Description Default Interdigit (10 ms) Specifies the amount of time the VoIP Subsystem waits after the dial string has matched a dial pat

Parameter Description Default Timeout Disconnect (10 ms) The range is 0 to 65535 in units of 10 ms 85 (850 ms) Timeout Warning (10 s) When the t

10 Feature Codes Feature codes are used to access advanced Class 5 telephony features. You can use the VoIP -> Advanced VoIP Settings -> Feature

1 Introduction This document describes the ADSL X6v modem's VoIP features. It provides information about the VoIP configuration parameters and ex

Parameter Description Default Do Not Disturb Enable Enter do not disturb state *78 Do Not Disturb Disable Exit do no disturb state *79 Blocked N

NOTICE This document contains proprietary information protected by copyright, and this Manual and all the accompanying hardware, software, and documen

Downloading Configuration Files Configuration files are prepared and stored on the service provider’s update server. At power up, reboot, or configur

2 Changing Configuration Parameters As administrator (admin), you can view and modify the VoIP configuration parameter values described in this Techni

3 System Parameters You can use the VoIP -> Advanced VoIP Setup -> VoIP System menu to configure overall system settings. The menu items inclu

Parameter Description Default NTP IP Address Fully qualified domain name (FQDN) (including an optional port number) for the NTP/SNTP timeserver ser